| Turning Your Pager On
1. Set the power switch to ON. Your pager emits an alert tone,
blinks and displays all digits on the LCD showing that your pager
is operating normally.
2. Press the power switch to reset the alert and press it again
to change the "ON" display. When the power switch is pressed
one more time, "0" is displayed at the left end of the
LCD showing that no information has been memorized.
Receiving Messages:
1. When receiving a new page, the tone alert sounds (or vibrates)
for eight seconds. In "N" mode, the tone will escalate
in volume after the first 4 beeps. The digital message will appear
on the screen.
2. The message remains on the display until you click the POWER
switch. If the message is longer than the display allows, an arrow
indicator appears in the upper right-hand corner. Click the POWER
switch again to see the rest of the message.
3. To return to the standby mode, click the POWER switch again.
Saving Messages:
You can save up to 6 messages for up to 7 days.
1. Click the POWER switch until the message you wish to save appears
on the display.
2. Double-click the POWER switch. Note the message begins flashing
along with the Save Message indicator (looks like a Key at top of
screen center). If KEEP FULL appears you have already saved 6 messages.
3. To save the message, click the POWER Switch. Note the Key indicator
remains on the display.
Deleting Messages:
One-At-A-Time:
1. From the standby mode, click the POWER switch until the message
to be deleted appears on the display.
2. Double-click the POWER switch and note the flashing Save Message
indicator appears. Double-click again and note the flashing Delete
Message indicator (looks like a star burst) appears.
3. To delete the present message, click the POWER switch. (Double-click
to return to the original message without deleting).
Deleting All Stored Message (Saved messages are NOT deleted with
this procedure):
1. From Standby mode, click the POWER switch until all messages
have been displayed and the memory used message appears.
2. Double-click and observe the "All delete" message flashes.
3. To cancel delete operation, double-click the power switch
4. To delete all messages (except save messages), click the POWER
switch.
Setting Date & Time:
1. Slide Power Switch to OFF position (all the way up)
2. Press and slide from OFF to N position (Keep holding in pressed
position)
3. Keep holding until the alert tone stops (approximately 8 seconds)
4. Observe the flashing "month" digit.
5. Press the power switch once (click) to step to the next month
digit, keep on pressing until you have reached the desired month.
(Go slowly and carefully, double click sets you back to the standby
mode - you will have to start over.)
6. Double click to confirm the month setting.
7. Proceed to the day of the month and following steps 4 thru 6.
8. Proceed to the hour of the day and follow steps 4 thru 6.
9. Proceed to the minute of the day and follow steps 4 thru 6.
10. Double click to save all settings and return to the standby
mode.
Setting the Alarm:
1. From the standby mode - double click - AL ON will appear
with a flashing bell symbol above.
2. Click once - Top left will show the hour blinking on a small
clock above the word ON.
3. Click slowly to get to the hour desired - double click to confirm.
4. Minutes will start to blink - click slowly to get to the minutes
desired - double click to confirm.
5. Small clock and the word ON will start to blink - Double click
to save settings.
6. Stand by mode will show a small bell in the top area above the
hour digit.
To Turn Alarm Off:
1. From the standby mode - double click 2 times quickly.
2. The word OFF will appear and blinking.
3. Click once to confirm turning alarm off - the bell symbol will
disappear on the display.
To Activate Auto On:
1. From the standby mode - double click 3 times quickly.
2. The word AUTO ON will appear with a small clock symbol in the
top right side.
3. Click once and the screen will show the word OFF and the hour
blinking on a small digital clock above the word OFF.
4. Slowly click until you get to the hour desired - double click
to confirm.
5. The minutes should start blinking - click until you get to the
desired minutes - double click to confirm. This is the time the
pager will turn itself off.
6. The word ON will appear on the screen - click to get the desired
time for the pager to turn itself back on - double click to confirm.
7. Minutes will start flashing - click to get to desired minutes
- double click to confirm.
8. Click to confirm setting auto on/off.
To change the type of Beep:
1. From the standby mode - double click 4 times quickly. The
word BEEP will appear.
2. Double Click to proceed to the next beep mode - double click
to get to each additional mode.
3. When desired beep is achieved - click once to save the setting.
|
